- HP ILO 4 WEB INTERFACE NOT WORKING HOW TO
- HP ILO 4 WEB INTERFACE NOT WORKING ACTIVATION KEY
- HP ILO 4 WEB INTERFACE NOT WORKING PASSWORD
- HP ILO 4 WEB INTERFACE NOT WORKING SERIES
Step 5: iLO Amplifier Pack InfoSight Configuration With the servers added we now need to connect the appliance to InfoSight. In my lab I only have three servers right now so I add all three and they appear to be reporting into the appliance. Add all your servers to the appliance using the above procedure.
HP ILO 4 WEB INTERFACE NOT WORKING PASSWORD
Just like before you enter the iLO IP Address of the server as well as the Username and Password and click Add when done. From here if you have additional servers to add you can click the + Add Server button at the top. The server will then show up in the Server Management section showing details about the server. Once the server is added it will query the iLO interface and gather data from it. Enter the iLO IP Address of the server as well as the Username and Password and click Add when done. Click on the Discovery section on the left. Step 4: iLO Amplifier Pack Server DiscoveryĪdding a server to iLO Amplifier is a very simple process.
Now we need to get servers added and InfoSight connected. Congratulations! iLO Amplifier Pack is successfully deployed. You should be presented with the iLO Amplifier Pack Dashboard now.
HP ILO 4 WEB INTERFACE NOT WORKING ACTIVATION KEY
Copy the Activation Key from the email and paste it into the box and click Activate. If you remember this is at the bottom of the email we initially received when registering for the iLO Amplifier Pack during Part 1 of this series. The first thing that comes up is the Welcome page asking for the Activation Key. Open a browser and navigate to the IP address you set on the appliance in the following format, Login to the appliance using the Administrator credentials supplied during the setup. You could also adjust any settings you may have entered incorrectly from the console here if needed. After a few minutes you should get the following screen which indicates the appliance is booted and can be accessed through a browser now. The appliance will restart and display the iLO Amplifier Pack loading screen. It will prompt you to reboot here and we just select Reboot to complete the setup. At this step you have to set a password for the Administrator account. Next up we set the timezone and enter NTP and a secondary external NTP and click Next. In my lab I only have one domain controller so I add it as well as a secondary external DNS provider and click Next again. I didn’t need that so I left NIC 2 disabled and select Next to continue. You can configure the appliance with one nic on the internal network and one nic on an external or perimeter network. For my deployment I chose to only use one NIC. On NIC 1 you have to configure the IPv4 Address, Subnet Mask and Default Gateway and then select Next. If you’re bored go ahead read the EULA or just select Accept and hit enter to continue.
In the console session select Initial Setup and hit enter.
After the appliance powers up you will need to open a Console session to the VM to continue configuring it. We just finished deploying the iLO Amplifier Pack Appliance in our vSphere environment and we powered on the appliance. Let’s continue from where we left off! Step 3: iLO Amplifier Pack Appliance Configuration In Part 2 we’re going to complete the iLO Amplifier configuration, perform server discovery in iLO Amplifier, configure it for InfoSight, do some troubleshooting and check out some of the features and functionality of HPE InfoSight for Servers.
HP ILO 4 WEB INTERFACE NOT WORKING HOW TO
I talked about the prerequisites, how to update iLO firmware on your servers, how to get the iLO Amplifier Pack and how to deploy it in vSphere. What it is, what it does and a bit about how it works.
HP ILO 4 WEB INTERFACE NOT WORKING SERIES
In Part 1 of this series I talked about InfoSight and specifically InfoSight for Servers. Welcome back! This is Part 2 of my Setup Guide for HPE InfoSight for Servers. HPE InfoSight for Servers – Setup Guide – Part 2.HPE InfoSight for Servers – Setup Guide – Part 1.
0 kommentar(er)
